KraftMaid Windows & Doors Nationwide

KraftMaid Windows & Doors: The Redwood City Owner’s Guide

We stock and install KraftMaid-compatible windows and doors across Redwood City, with typical replacement costs running $4,500-$15,000 for full window replacement and $8,000-$25,000 for impact-rated installations depending on series and opening count. Most KraftMaid hardware, sash balances, and weatherstrip components are on our trucks or available next-day through our Peninsula supply chain. Homeowners usually discover a problem when a window won’t stay open, a door drags on the jamb, or they feel a draft along the sill during a Redwood City winter storm.

Call (650) 560-7228

Which KraftMaid Models This Applies To

KraftMaid’s window and door program spans several series, and the parts are not interchangeable across generations. The current Vantage and EpicVue window lines use a proprietary cam-lock and tilt-latch system with a 1-3/16″ backset that differs from the older KraftMaid Classic series, which used a standard 7/8″ backset discontinued around 2018. If your unit was installed before 2018, check the jamb sticker for a four-digit date code and the letter series (C for Classic, V for Vantage, E for EpicVue).

We carry OEM KraftMaid tilt latches, sash balances, and multipoint hardware, plus quality aftermarket equivalents from Truth Hardware and AmesburyTruth where the OEM lead time stretches past a week. The aftermarket route saves roughly 15-20% on parts cost and carries the same 10-year finish warranty, but we always verify the exact shoe depth and tube diameter before ordering. A Classic series balance with a 5/8″ tube will not seat properly in a Vantage frame, and we’ve learned that the hard way on a Stambaugh-Heller craftsman where the previous owner had mixed generations.

Signs Your KraftMaid Windows & Doors Is Failing

• Window drops or won’t stay open. The coil or block-and-tackle sash balance has lost tension, usually from metal fatigue after 8-12 years of Redwood City’s marine temperature swings. The balance is doing the work your arm used to do; when it fails, the sash becomes a guillotine hazard.
• Door sticks in summer, gaps in winter. The composite jamb has absorbed moisture and swollen, or the hinge screws have backed out from seasonal expansion cycles. In Redwood City’s clay-heavy soil zones, subtle frame shifts compound the problem.
• Visible condensation between glass panes. The insulating glass unit (IGU) seal has failed, releasing the argon fill and allowing moisture migration. Once the desiccant saturates, the clouding is permanent and the thermal performance drops to roughly that of single-pane glass.
• Multipoint lock handle spins without engaging. The gearbox inside the mortise mechanism has stripped, often from forcing the handle when the door is misaligned. Continuing to operate it risks snapping the spindle and damaging the faceplate mortise.
• Draft along sill or meeting rail. The bulb-style weatherstrip has compressed past recovery or the pile fin seal has shed its fibers. Redwood City’s salt air accelerates rubber degradation compared to inland climates.

Before

After

Replacement Cost & What’s Included

For KraftMaid window and door work in Redwood City, our installed pricing breaks down as follows:

• Window Replacement: $4,500-$15,000 (typical 8-12 opening home)
• Impact Window Installation: $8,000-$25,000 (required in some FEMA flood zones near Redwood Creek)
• Balance/tilt-latch hardware repair: $180-$340 per opening
• IGU replacement (glass only): $275-$550 per sash
• Multipoint lock mechanism: $320-$680 installed
• Weatherstrip replacement (full perimeter): $95-$195 per opening

The range reflects unit size, floor height (third-story work requires scaffolding), and whether the interior trim can be salvaged. Every quote is a flat written price with line-item parts and labor, signed before work starts under Clause 1 of the Haven Standard. Our 365-Day Done Right Promise covers the installation and the hardware function; manufacturer defects go through the OEM warranty channel, which we handle as part of the job.

DIY or Call Us?

An owner can safely inspect the jamb sticker, measure the visible glass dimensions, and photograph the lock faceplate for identification. What goes wrong fast: sash balances store significant tension and can release violently if the retaining clip is removed without a balance-loading tool. We’ve seen lacerations and broken glass from homeowners who watched a five-minute video and skipped the safety step.

Multipoint lock gearboxes require precise mortise depth; 1/16″ too deep and the latch bolt won’t throw fully. We don’t recommend DIY on any component under spring tension or involving structural load transfer. If you’re unsure which series you have, call us at (650) 560-7228 and we’ll walk through the identification over the phone. Measure twice, document once, build it so it doesn’t come back.

FAQs